Programming instructions for Blackweb universal remote controls

Programming instructions for Blackweb universal remote controls (models: BWB17AV002, BWA18AV007C, BWB18AV004 and BWA18AV007):

Code entry instructions

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the device button (e.g., "TV", "SAT/CBL", "STREAM", "B-RAY/DVD", "AMP", "AUX") you want to program. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Enter a 4 digit code. If the code is valid, the "POWER" button's indicator light shuts off. If it flashes and then remains on, it means an invalid code was entered and you must re-enter the code.

Step 4: Test the remote with the device to make sure the buttons work as expected. If all work, setup is complete. If not, repeat this process using a different code.

Blackweb BWB17AV002 Universal Remote Buttons (img)

Blackweb BWB18AV004 Universal Remote Buttons (img)

Blackweb BWA18AV007 Universal Remote Buttons (img)

Code search

Step 1: Turn on your device.

Step 2: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 3: Press the device button (e.g., "TV", "SAT/CBL", "STREAM", "B-RAY/DVD", "AMP", "AUX") you want to program. The "POWER" button's indicator light will blink once and will remain on.

Step 4: Point the remote at the device you wish to control and then press and hold the "OK" button until the device turns off. The "POWER" button's indicator light will blink as the codes are being tested. When the device turns off, immediately release the "OK" button to lock in the code. The indicator light will turn off.

Step 5: Test the remote with the device to make sure the buttons work as expected. If all work, setup is complete. If not, repeat this process.

Notes:

• It may take over 10 minutes to scan through all the possible codes for your device.
• If during the 'Code Search' procedure you have either accidentally or deliberately released the "OK" button, you may repeat steps 2 through 5 above to resume the code search where it left off.
• When 'Code Search' has exhausted all available codes for the selected device, the "POWER" button's indicator light will blink 3 times and turns off. If none of the codes worked with your device, your Blackweb universal remote is probably not compatible with the device.

Code Retrieval

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the device button (e.g., "TV", "SAT/CBL", "STREAM", "B-RAY/DVD", "AMP", "AUX") you want to find out the code for. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the red "A" button. The "POWER" button's indicator light will blink once and will remain on.

Step 4: Press the "1" button. Count the number of times the "POWER" button's indicator light flashes. This is the number corresponding to the first digit of the code. If the button does not flash, the corresponding code number is 0. Repeat the process by pressing the "2", "3" and "4" buttons for the remaining digits.

Step 5: Press the red "A" button to exit 'Code Retrieval' mode.

Favorite Channels

For easy access to up to 10 of your favorite channels, follow the steps below:

Step 1: Press the device button that controls the channels. The "POWER" button's indicator light will blink once and will remain on.

Step 2: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 3: Press the "FAV" button. The "POWER" button's indicator light will blink once and will remain on.

Step 4: Select the button ("0" to "9") that you will use for storing your favorite channel. The "POWER" button's indicator light will blink once and will remain on.

Step 5: Enter the channel number you wish to program as a favorite channel.

Step 6: Press the "FAV" button. The "POWER" button's indicator light will turn off and the channel is saved.

Notes:

• To access your preprogrammed favorite channel, press the "FAV" button, then press the programmed button ("0" to "9") for that channel.
• To change a stored favorite channel, repeat steps 1-6 above.

Volume Lock

Use this feature to lock a device to the remote's volume control. For example, the remote can be in TV mode while the volume buttons control your Sound Bar.

Enabling Volume Lock:

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the device button (e.g., "TV", "SAT/CBL", "STREAM", "B-RAY/DVD", "AMP", "AUX") you want to lock to the remote's volume control to. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the "VOL+" button. The "POWER" button's indicator light will blink once and will remain on.

Step 4: Press the "OK" button. The "POWER" button's indicator light will blink twice and then turn off.

Disabling Volume Lock:

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the "VOL-" button. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the "OK" button. The "POWER" button's indicator light will blink twice and then turn off.

Note:

• On most newer HDMI-connected devices, the 'Volume Lock' feature may be unnecessary as this feature is already built-in.

Channel Lock

Use this feature to lock a device to the remote's channel control. For example, the remote can be in TV mode while the channel buttons control your satellite or cable box.

Enabling Channel Lock:

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the device button (e.g., "TV", "SAT/CBL", "STREAM", "B-RAY/DVD", "AMP", "AUX") you want to lock to the remote's channel control to. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the "CH+" button. The "POWER" button's indicator light will blink once and will remain on.

Step 4: Press the "OK" button. The "POWER" button's indicator light will blink twice and then turn off.

Disabling Channel Lock:

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the "CH-" button. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the "OK" button. The "POWER" button's indicator light will blink twice and then turn off.

Note:

• On most newer HDMI-connected devices, the 'Channel Lock' feature may be unnecessary as this feature is already built-in.

Reset to factory default settings

Step 1: Press and hold the "PROGRAM" button until the "POWER" button lights up red. The light will remain on.

Step 2: Press the "*" button. The "POWER" button's indicator light will blink once and will remain on.

Step 3: Press the "OK" button. The "POWER" button's indicator light will flash twice and the remote will revert to factory settings.