OneForAll Streamer programming instructions

The OFA Streamer remote is preprogramed to control a Roku streaming box and a Samsung TV or a TCL brand Roku TV, depending the retailer where you bought the remote. However it can also be programmed to control another brand of streamer as well as the Volume, Mute, Input and Power of your TV, or the Volume and Mute of your Sound Bar.

Direct code entry

Each brand has a list of 5 digit codes per device. The codes all consist of numbers between 1 and 6. You can enter the code using the "TV Power", "Streamer Power", "Back", "Home", "Replay" and "Options" keys to represent the numbers.

Key Name	Digit
TV Power	1
Streamer Power	2
Back (←)	3
Home (⌂)	4
Replay (⟲)	5
Options (*)	6

For example, to enter the code 23161 for a Vizio TV you would press "Streamer Power" (2), "Back" (3), "TV Power" (1), "Options" (6) and "TV Power" (1).

Step 1: Turn on your device (not on standby) and point the remote towards it.

Step 2: To set up:

TV set: hold down "TV Power" and "Back" until the yellow LED under the ring blinks twice.

Streamer: hold down "Streamer Power" and "Home" until the red LED under the ring blinks twice.

Audio device: hold down "Volume+" and "Volume-" until the green LED under the ring blinks twice.

Step 3: Enter the first 5 digit code listed for your brand using the "TV Power", "Streamer Power", "Back", "Home", "Replay" and "Options (*)" Keys to represent the digits. The green LED will blink twice.

Step 4: Now aim the remote towards your device and press the "Power" (or "Mute") key.

Step 5: If the device turns off (or mutes), your remote is ready to use. If not, repeat the procedure with the next code in the list.

Notes:

• If you find one or more keys do not work as you expect, start again at step 2.
• Your remote can operate up to three devices. Most keys will control your streaming box, but you can control some functions of your TV and Sound Bar or Audio Video Receiver If you set up a TV, the "Volume Up", "Volume Down", "Mute", "TV Power" and "TV Input" keys will then control your TV. The menu ring will light up in yellow to show you are controlling the TV. If you then also set up an Audio Device such as a Sound Bar or Audio Video Receiver, the remote will then control the Volume Up, Down and Mute of that device. The menu ring will light up in green to show you are controlling the Audio Device.
• As the TV Input key is intended to select the input on your TV and most TVs use a menu to select from a list of inputs, when the "TV Input" key is pressed and a TV is set up, the "Menu Up", "Down", "Left", "Right" and "OK" keys temporarily control the TV. If the "OK" key is pressed, or no key is pressed for 10 seconds, these keys will revert to controlling your streamer.

Learning

Your One For All remote control can learn any function from any other working remote control. This is a quick and easy one-time setup that will allow you to control one or more of your home entertainment devices, and even combine multiple devices in one easy to use remote control. You could, for example teach the volume keys to control your Sound Bar, the TV Power and Input keys to control your TV, and the rest of the keys to control a Streaming box.

To do this, first make sure you have all your original remote controls to hand, and that they have working batteries in. To learn functions, the original remote should be approximately 3cm from the OFA remote, pointing towards it.

Step 1: Hold down "TV Power" and "Mute" until the red LED blinks twice.

Step 2: Press and release the key you want to learn a function onto. The red LED will blink once and go out.

Step 3: Press and release the corresponding key on the original remote.

Step 4: The red LED will blink green twice to indicate the key has been learned correctly.

Step 5: Repeat steps 2 and 3 for each key you want to learn.

Step 6: When you learned all the functions you require, press and hold the "TV Power" key until the green LED blinks 4 times.

Notes:

• You can learn from multiple remotes, but only one function per key.
• Some remotes send commands differently. If you find a function cannot be learned, try holding down the key on the original remote instead of pressing and releasing.
• If the red LED shows one long blink at step 4, the function was not learned correctly, try again from step 2.
• If you find that one or more keys don't work properly after set up, you can re-enter the learning mode at any time by repeating the procedure from step 1.
• To delete a learned function, hold down "Streamer Power" and "Mute" until the red LED blinks twice, and press the key to delete twice.