eliztech.com logo
Remote Controls > U-verse A10 programming

AT&T U-verse A10 Advanced Series programming

Uverse A10 Advanced Series remote control

Direct code entry

Use the following steps to set up the TV, DVD or AUX mode keys:

Step 1: Press and hold the mode key ("TV", "DVD" or "AUX") and while holding it pressed, press the "OK" key for one second. Release both keys. All of the mode keys will flash and the selected mode key light will stay lit.

Step 2: Enter the 4-digit code by pressing the numerical keys (0-9). The selected mode key light will blink for each digit entry and will remain off after the entry of the 4th digit, indicating successful set-up.

Step 3: Point the remote control at the selected device and press the power key once. The device should turn off. If the device stayed on, repeat this procedure trying each code for your brand until you find the correct code.

Notes:

  • If an invalid code is entered or no key is pressed at all for 30 seconds, the mode key light flashes for 3 seconds and turns off. The remote control returns to normal operation and you will need to start over.
  • To use the remote control for your U-verse unit, press the AT&T mode key.
  • The DVD and AUX mode keys can be set up with any code. The TV mode key can only be set up with TV codes.

Using the search function

Note: To search for a particular device code for DVD or AUX e.g., VCR, use Direct code entry and program DVD or AUX with any VCR code prior to starting a search.

Step 1: Turn on the device you want to control and point the remote at that device.

Step 2: Press and hold the mode key ("TV", "DVD" or "AUX") and while holding it pressed, press the "OK" key for one second.

Step 3: Release both keys and all of the mode keys will flash then the selected mode key light will stay lit.

Step 4: Press the power button repetitively until the selected device responds. Once your device has responded, press "OK" to save the code. To indicate a successful set up, the selected mode key will turn off.

 

Learning Commands

If the code for your device is not found in the code lists and the search feature does not work with your device, then the learning feature may be your best option. The learning feature lets you "learn" functions from your original remote control.

Step 1: Press and hold the mode key ("TV", "DVD" or "AUX") and while holding it pressed, press the "LEARN" key for one second then release both keys.

Step 2: All of the mode keys will flash and then the selected mode key light will remain on.

Step 3: On your U-verse remote control press and release the key that you want to teach.

Step 4: While pointing your original remote at the bottom of your U-verse remote approximately one inch apart, press and hold the original remote key until the mode key light blinks once and stays on. (If there is a learning problem, the mode key light blinks for 3 seconds and stays on. If this happens, repeat the steps above.)

Step 5: Repeat the steps above for each key you want the U-verse remote to learn. Press and release the "LEARN" key when all desired remote commands have been learned.

Note: It's not necessary to have your U-verse remote control learn every command from your original remote since most of the keys will not be used under normal daily use. Best practice is to teach only the keys that help you navigate for the best experience, like the Volume Up/Down, Channel Up/Down and DVR functions.

Clearing Commands

To clear all learned commands (under a single mode):

Step 1: Press and hold the mode key ("TV", "DVD" or "AUX") and while holding it pressed, press the "LEARN" key for one second, then release both keys.

Step 2: All the mode keys will flash and the selected mode key light will stay on.

Step 3: Press and release the "LEARN" key once. The mode key light blinks off.

Step 4: Press and release the "DELETE" key. The mode key light turns off. All learned commands under that mode are now cleared.

To clear all learned commands (under ALL modes):

Step 1: Press and hold the mode key ("TV", "DVD" or "AUX") and while holding it pressed, press the "LEARN" key for one second, then release both keys.

Step 2: All the mode keys will flash and the selected mode key light will stay on.

Step 3: Press and release the "LEARN" key twice. The "TV" mode key light blinks off.

Step 4: Press and release the "DELETE" key. The "TV" mode key light turns off. All learned Commands in the remote are now cleared.

 

Resetting the remote control to the factory default settings

Step 1: Press and hold the "TV" key and while holding it pressed, press the "OK" key for one second, then release both keys.

Step 2: All the mode keys will flash and the "TV" mode key light will stay on.

Step 3: Press and hold the "DELETE" key for 3 seconds until the "TV" mode LED blinks and stays off. The remote control is now reset to factory default settings.